Set Specific Directions
Wall Mount for LEGO® Yoda™ (75255)
Assemble the Yoda (75255) tray with two Large brackets before marking the wall. The animation shows the tray, recessed M3 hardware and drywall installation for this specific mount.
Reference 75255
These instructions apply to this item. Follow the steps below and any item-specific notes.
Purchase this itemBefore you start
Tools needed
- Screwdriver with a bit that fits the supplied screws
- Level
- Fine-tip pen or pencil
- Stud finder, if needed
- Drill and drill bit, if needed for your screws or anchors
- Tape measure, if needed
Parts & hardware
- 1 shaped display tray
- two Large brackets
- 4 low-profile M3 screws and 4 washers for tray assembly
- Wall hardware for 8 mounting holes, with suitable anchors where needed (wall hardware supplied only if ordered)
Check your parts and separate the hardware
Lay out the tray, all supplied brackets, and the included M3 screws and washers before you begin. Check that the tray and brackets match the mount you ordered and that the printed parts are free from visible damage. Keep the assembly hardware and wall-mounting hardware separate: the M3 screws and washers attach the tray to the brackets; the wall screws and anchors secure the assembled mount to the wall. The M3 assembly screws are not substitutes for wall-mounting screws. If you did not order wall hardware, have suitable screws and any required anchors ready before installation. Leave your set off the tray until the mount is fully assembled and securely installed.
Align the empty tray with the Large brackets
Work on a stable surface. Match the recessed tray holes to the pre-installed threaded inserts in two Large brackets. Orient the flat wall-mounting faces as shown in the animation. Keep the model off the tray during assembly.
Fasten the tray to the brackets before marking the wall
Place a washer in each of the 4 tray recesses. Start each low-profile M3 screw by hand through its washer and into the aligned insert. Tighten evenly until snug. Check that the tray sits firmly against each support before lifting the assembly.
Use the assembled mount to mark the wall
Check for hidden services and choose appropriate wall hardware. Hold the empty, fully assembled mount level at its intended height. Use a pencil to mark all 8 wall holes through the installed brackets. Set the assembly aside before drilling.
Prepare the wall for screws and anchors
Check that the screws and anchors you plan to use are appropriate for the wall and the completed display. Follow the screw or anchor manufacturer’s instructions for hole size, drilling depth, anchor installation, and screw compatibility. If anchors are required, prepare the marked holes and fit the anchors as directed. For screws going into a stud, prepare any pilot holes required by the screw manufacturer. Check for concealed wiring or pipes before drilling. Keep the mounting-hole locations aligned with the marks you made from the assembled mount. If an anchor spins, a hole is damaged, or a screw or anchor will not hold securely, correct the problem before attaching the mount. Do not rely on tightening harder to repair a loose screw or anchor.
Secure the assembled mount to the wall
Support the empty mount and align each bracket’s wall-mounting holes with the prepared positions. Insert the appropriate wall-mounting screws and start them before fully tightening any one screw. Use all wall-mounting holes required for the supplied brackets. Check the assembly’s alignment, then tighten the wall screws gradually until the brackets are held securely against the wall. Keep the mount supported while tightening. Avoid overtightening or forcing the printed brackets to bend against an uneven surface. Gently check the empty mount for rocking or movement, and check that the tray-to-bracket M3 connections remain secure. Do not pull on the tray or hang extra weight from it as a test. If a bracket moves, a wall screw or anchor loosens, or the tray does not sit as intended, stop and resolve the issue before placing your set.
Place the set on the installed tray
Support the assembled figure from below and lower its base onto the tray. Check that the lightsaber and the tips of the ears clear the wall and nearby objects. Release your hands gradually. If the model rocks or the mount shifts, lift it off and check the fit and fasteners. Support the base when removing the display.